PRODUCTS |
BRUSH MACHINE |
||||||||||||||||||
BRUSH MACHINE | ||||||||||||||||||
Use | ||||||||||||||||||
The Machine is meant for final cleaning at the part end of screen room & placed before grinding for removing dust striking to the crease and the outer surface. | ||||||||||||||||||
|
||||||||||||||||||
Hammer Mill |
Hammer Mill | |
Vertilated Hammer Mills are used for grinding of crushing of soft or half-hard material, dry or with a relatively small humidity non-clogging upto a fitness. They are mainly used for :- | ||
i) | Agricultural Purposes : For Grinding of Corn, bran, Oat, Barley, dry, Maize, | |
Whenstraw, Straw forage, Oil-cake, Eark, some roots, some dry fruit, | ||
vegetables, etc. | ||
ii) | For food stuffs and extic goods : As dried Vegetables, chocolates, nuts dried | |
milk, powderly sugar, salt, etc. | ||
iii) | Chemical industry : They are also used in the industrial Sector as help solution (temporary or emergency use) Mill Lime, chalk, Gypsum, Clay asbestos, certain chemical goods (resin colour) and other products (Paper wood chips), etc |
Operation |
The material is handled on a conveyor inside the Mill itself in which the hammer are rotating and high speed. The material is caught by these hammers thrown against the Mill. A face caught again and broken down until the required fitness is reached, it is passing through a screen or a perforated steel plate falls down in under part of the mill. A fan draws it out and Blows it to a dusting cyclone for storage. A Value under the cyclone may be opened and ground material is easily collected. |
Main Characteristics of Mills |
|
TYPE | H X W X L. | R.P.M. | Kg. /Hr.Per | Mesh Size |
HR 7 - 14 | 10' X 3' X 3' | 2300 | 50 Kgs | 30 to 080 |
HR 9 - 18 | 10' X 4' X 4' | 2800 | 150 - 200 Kg | 30 to 080 |
HR12 - 18 | 10' X 5' X 5' | 2800 | 400 Kgs | 30 to 080 |
Pin Mill Pulverizer |
Pin Mill Pulverizer |
Pin mill is intended for the grinding of all kinds of material as grains and pulses. The pin mill is fed from the center and is grinding with adjustable speeds through three passages out towards the periphery, By means of this successive processing of the material to smaller and smaller particles, The materials to be ground gets exactly the predetermined structure. |
Materials | Capacity In Kgs / Hour |
Wheat Barley etc, | 250 to 280 kgs. |
Rice, Gram Pulse (Bason) etc. | 300 to 400 kgs |
Charcoal | 160 to 380 kgs. |
Spices as Chilly etc, | 100 to 120 kgs |
Soya bean cakes etc | 1100 to 1800 kgs |
Coal Plaster (Chemicals) | 1200 to 1800 kgs. |
Max Height (MM) | Dimensions Depth(MM) | Width (MM) | Dia of Rotor (MM) | H.P. Req. | R.P.M. For Motor | Recommended for R.P.M. Machine |
1400 | 980 | 880 | 495 | 15-20 | 2880 | 2000-3000 |
Centrifugal Dressing Machine |
Centrifugal Dressing Machine | |
Centrifugal Dresser | ||
The machine consists of a polygonal reel or barrel covered with Nylon or wire contained in Steel Frame with hoppered bottom | ||
Beaters | ||
Inside the machines are rapidly revolving beaters so designed as to Lift the stock and direct it obliquity across the Nylon. The distance of the beaters from the Nylon are adjustable. | ||
Spiral Brush | ||
A brush is fitted for keeping the meshes clean and open. A worm conveyor is fitted at the bottom of the hoppering of the machine to take away the fine stock which has been dressed through the meshes of the meshes of the Centritagal M/C. | ||
Size of Machine | Extreme Length | Extreme Width | Extreme height | R.P.M. of M/C | H.P. Required | No. of Sheets | Feed |
30" diam | 14' | 14" | 60" | 200 to 250 | 3-0 | 2.5/3 | single |
|
Emery Chakki |
SALIENT FEATURE : | |
(1) Highest feature results with regard both to quantity and quality. | |
(2) Very low Power consumption because of the Emery Stones run with double roller bearings. | |
(3) Semi Automatic feed mechanism for all kinds of grain. | |
(4) Emery Stones are made under great care with experienced manufacturers. | |
ACCURACY AND REALIABILITY : |
The greatest care is exercised in the construction of Emery Chakki to ensure perfect accuracy and reliability. All parts are made to jigs and templates and are of the good materials and workmanship through out the process. The Machines are carefully driven at factory and well inspected. |
CONSTRUCTION : |
The machine structure is made from heavy duty and heavy plate and sheet. All shafts are made from En series and well grid finishing. The bearings are used of well known made from reputed dealers. All parts are manufactured by all latest machines and all fabricated items are fabricated bu jigs and welded by transformer welding under great care. |
TECHNICAL
DETAILS
|
|||||
Chakki
Size(In MM)
|
Emery
Size(In MM)
|
Pully
Size(In MM)
|
H.P.
|
RPM
|
Production
per Hr.
|
400
|
400
|
250
|
5-7.5
|
600
|
130-200
Kg.
|
500
|
500
|
300
|
7.5-10
|
600
|
200-250
Kg.
|
600
|
600
|
350
|
10-15
|
500/550
|
280-300
Kg.
|
750
|
750
|
400
|
15-20
|
400/450
|
350-400
Kg.
|
Accessories | ||
The accessories like Rubber lids, oval Ball, tri-angle brushes, round ball etc are used in cleaning section screen room and also in milling section screen room. All types of brushes are manufacturing as per requirement and also as per design. | ||
Accessories |
||
Top |